-
×
Intake Manifold Gaskets Set 5184562AC 5184331AC For 2011-2020 Chrysler Jeep Dodge Ram 3.6L V6
1 × $15.99
Subtotal: $15.99
O2 Oxygen Sensor Spacer Extension Car CEL Fix Check Engine Light Eliminator Adapter M18X1.5, 32mm/1.25in
$8.99 – $130.00
Easy to fix CEL;
Made from Steel, Zinc coated;
Easy installation;
M18 X 1.5 thread fit for most exhaust systems.
How does It work?
This O2 Sensor Spacer works on competitive racing vehicles by moving the post-cat oxygen sensor out of the direct exhaust flow. It effectively reduces the amount of exhaust gas exposed to the oxygen sensors tip to that of a normal production street vehicle. This O2 Sensor Spacer usually clears the p0420 and p0430 check engine light codes (cel) 95.9% of the time., if the p0420 or p0430 cel is illuminated the engine control unit (ECU) will put the vehicle into “limp mode” (safe mode) resulting in poor performance and gas mileage, not to mention it’s pretty annoying seeing that check engine light on all the time.
O2 Sensor Spacers are only installed on the post cat (rear) oxygen sensors usually located at or slightly past the catalytic converter. Vehicles have either one or two post-cat oxygen sensors and an o2 simulator should be installed on each post-cat sensor to remove p0420 and p0430 and check engine light codes for a bad or missing catalytic converter.
FITMENT, will it fit my vehicle?
This O2 Sensor Spacer is threaded 18mm x 1.5 which is the size of 99% of vehicles produced. Check your owner’s manual, and performance data or just crawl up under there, locate the post-cat sensor and put a 7/8 inch or 22mm wrench on the hex portion of the oxygen sensor if the wrench fits then you have 18mm x 1.5 threads. Correct fitment is your responsibility, please take the time to check.
Clearance, how much room is needed for installation?
The only issue for clearance is the length of the O2 Sensor Spacer and Oxygen Sensor combined as measured from the exhaust pipe to the oxygen sensors wire tip. This length is 4.5 inches (115mm) so imagine your presently installed oxygen sensor is 2 inches longer than it is, that’s how much clearance you need to install this type of O2 Sensor Spacer. It is your responsibility to ensure there are no clearance issues.
How is the O2 Sensor Spacer Installed?
The O2 Sensor Spacer simply screws into your existing exhaust pipe using the same thread port where your post-cat sensor is located. Installation is easy, first, disconnect the oxygen sensor and unscrew it. Second, screw back in the O2 Sensor Spacer, then screw in the oxygen sensor, reconnect the oxygen sensor, and that’s it your done.
Please Note:
(1) This Does Not Fix A Defective O2 Sensor, Wiring or Heater Circuits.
(2) No…O2 Sensor Is Included In This Offer.
(3) Designed For Post Cat Sensor ONLY.
(4) Intended For Competitive Modified Exhaust Use Only.
(5) Do Not Use To Remove Cel Caused By Faulty Catalytic Converter!
(6) It is the buyer’s responsibility to check and verify Fitment and Clearance issues.
| Weight | 0.134 kg |
|---|---|
| Dimensions | 18 × 12 × 10 cm |
| Count | 2 Pcs, 4 Pcs, 10 Pcs, 50 Pcs, 100 Pcs |
Arabic
Chinese (Simplified)
Dutch
English
French
German
Italian
Portuguese
Russian
Spanish
joshua tiago –
Five Stars
worked fine and was a exact fit for the hole i needed to plug.
thanh le –
Will sieze if you get it good and hot..
Mine siezed up badly. Broke two extensions trying to remove the dang thing. Amazingly the hex head held up just long enough to finally remove it with an 18 inch breaker bar. After finally getting it out, about the first four threads were still in the bung. Took a few passes with a thread chaser to clean up. The other one I purchased, I was able to mount a few more inches downstream of the manifold. It has given me no problems at all. It must be made from quality steel. Hats off to the the hex socket for holding up to the amount of torque it took to remove it. Going to seek out a good anti-sieze that might possibly be able to handle that application.
Chris Downey –
Five Stars
2016 sti. Perfectt fitsThanks
Luis Fernando Rico –
Where is the crush washer?
There should be something in the package to use for a crush washer
David Bradley –
Dont forget the washer
Work fine but didnt come with a copper crush washer.
ramoncito g. de larama –
Dont worry about the measurement
It fits the porpoise..in my new pipe for the camry 2002
esteban malave –
good product
exactly what I needed. Prompt service. If every thing they sell is this good, count me a steady customer.
frank jahner –
perfectly. Works
Fit my o2 plug hole perectly.
William Hayden –
Good.
I didnt need it and they were cool to let me return it.
Jennifer Cox –
Exactly as advertised. Shipped quick
Plugged a wideband port while not using it. Worked great
Muhammed Ayuba –
Solid
Solid. Good price
Cocho Quijano –
Worked
Fit what I needed little over priced for a plug but when you need it you need it lol
sean wolk –
Fits Standard O2 Sensor Port
One of my o2 sensor plugs fell of my truck and this was an exact fit to replace it and better design as well.
vincent –
Works
I added a power commander to my motorcycle and no longer needed the O2 sensors. Instead of just disconnecting them, I removed them and used these to plug the hole. No crush washers weres included but it does not appear they are needed (no exhaust leaks without them). BMW r1200gs
samir samad –
Oxygen sensor cap
I like and fit perfectly
Gilberto Davila –
What I was looking for.
Perfect fit.
long dole –
Used as a rear differential fill plug
Needed a fill plug for the rear differential on a 2004 Pontiac Vibe AWD. Previous mechanics had stripped out the original hex plug. Used vice grips and a hammer to remove. Since the O2 sensor plug had the same specs and was basically the same, a new crushable washer and some antiseize compound seems to have done the trick and saved a few bucks off the OEM plug.
thuy thai –
Works great
Right part to close off a o2 sensor port for a Mazda 3. (2006)
Mark Cheslea Holley –
fittted perfect
great
tharwat hanna –
Nice piece
Fit like it should. No complaints
Mark Dizon –
Worked perfectly
Nice plug, did the job
weiwei Tan –
Works well
What can you say! It works.
MARTY CLUBB –
Good quality!
Well it work for me! Good quality and good price
Ray Roque –
O2 sensor plug
Worked great to plug an O2 sensor hole.
Richard Lee –
Victory Judge
Removed my O2 sensors on my Victory Judge. Easy install and looks clean! Apply anti-sieze!
N and S Auto Parts –
Perfect fit
Fits perfect on my Z900RS cafe.
Stephen Mcalister Jr –
Great prices easy to order fast shipping acute shipment tracking and great quality products
Carl Daniels –
Can’t wait to install it.
phillipe masse –
Anonymous –
Item exactly as described and fast shipping.
Waleed Itani –
Esteban Aguilar –
Excellent
Ken Ruhland –
Did not receive
yanne_0628 –
Hi, your parcel was delivered on Sept.-12,2024. You should received it now. Right?
2024-09-12 12:16 US, OH, New Richmond, Delivered.
Please contact us if anything wrong with it.